Product ID:SATINHIDE LO LUSTRE WHITE & PASTEL BASE, 20
MSDS Date:05/12/1990
FSC:8010
NIIN:00N025432
MSDS Number: BMQYN

PPG INDUSTRIES INC (WAS PTTTSBURGH PLATE GLASS CO)

260 KAPPA DR
PITTSBURGH, PA 15238
US

Emergency Phone: 304-843-1300

Info Phone: 412-963-5822; 412-492-5555

Cage: 47695

PPG INDUSTRIES INC

PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 20-25%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293

CARBONIC ACID, CALCIUM SALT; (CALCIUM CARBONATE)

CAS: 471-34-1

RTECS: FF9335000

Fraction By Weight: 20-25%

OSHA PEL 15MG/M3TDUST;5 RESP

ACGIH TLV: 10 MG/M3 TDUST

HYDROTREATED HEAVY NAPHTHA

CAS: 64742-48-9

Fraction By Weight: 30-35%

FILM FORMERS, RESINS & ADDITIVES

Fraction By Weight: 20-25%

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGEST: HARMFUL/FATAL IF
INGESTED. EYES: CAUSES EYE IRRIT. SKIN: MAY CAUSE MOD SKIN IRRIT.
INHAL: VAP & SPRAY MIST MAY BE HARMFUL IF INHAL. CHRONIC: AVOID
LONG TERM & RPTD CONTACT. CONTAINS TIT ANIUM DIOXIDE. ANIMALS INHAL
MASS QTYS OF TITANIUM DIOXIDE DUST IN STUDY DEVEL LUNG TUMORS.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:REDNESS, ITCHING, BURNING SENSATION & VISUAL
DISTURBANCES MAY INDICATE EXCESS EYE CONTACT. DRYNESS, ITCHING,
CRACKING, BURNING, REDNESS, & SWELLING ARE CONDITIONS ASSOC
W/EXCESS SKIN CONTACT.

First Aid:INGEST:DO NOT INDUCE VOM. EYES:FLUSH EYES IMMED W/PLENTY OF
H*2O FOR AT LEAST 15 MINS. SKIN:REMOVE PROMPTLY BY WIPING, FOLLOW
BY WATERLESS HAND CLEANER, SOAP & H*2O. INHAL:REMOVE TO FRESH AIR.
APPLY A RTF RESP/OTHER SUPPORTIVE MEASURES AS REQD. OTHER:IF ANY OF
THE FOLLOWING OCCUR CONTACT POISON CNTRL CNTR, EMERG RM/MD IMMED.
HAVE MSDS INFOR AVAIL. INGEST, EXCESS EXPOS TO CORRO MATL. (SUPP
DATA)

Flash Point Method:PMCC
Flash Point:120F,49C
Lower Limits:0.7
Extinguishing Media:USE NFPA CLASS B EXTING(CO*2/DRY CHEM/UNIVL AQUEOUS
FILM FORMING FOAM)DESIGNED TO EXTING CLASS II COMBUST LIQ FIRES.
Fire Fighting Procedures:USE NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
H*2O SPRAY MAY BE INEFTIVE. H*2O SPRAY MAY BE USED TO COOL CNTNRS
TO PVNT PRESS BUILDUP & POSS (SUPP DATA)
Unusual Fire/Explosion Hazard:KEEP CNTNRS TIGHTLY CLSD. ISOLATE FROM
HEAT, ELECT EQUIP, SPARKS, & OPEN FLAMES. CLSD CNTNRS MAY EXPLO
WHEN EXPOS TO EXTREME HEAT. DO NOT APPLY ON (SUPP DATA)

Spill Release Procedures:PROVIDE MAX VENT. ONLY PERS EQUIPPED W/PROPER
RESP & SKIN & EYE PROT SHLD BE PERMITTED IN AREA. REMOVE ALL
SOURCES OF IGNIT. TAKE UP SPILLED MATL W/SAWDUST, VERMICULITE, OR
OTHER ABSORB MATL & PLACE I NTO CNTNRS FOR DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QTYS IN BUILDINGS DESIGNED & PROTECTED FOR STORAGE OF NFPA CLASS II
COMBUST LIQS.
Other Precautions:IF MATL IS PART OF MULTIPLE COMPONENT COATING SYSTEM,
READ MSDS FOR OTHER COMPONENT(S) BEFORE BLENDING AS RSLTG MIX MAY
HAVE HAZS OF ALL ITS PARTS. CNTNRS SHLD BE GROUNDED WHEN POURING.
AVOID FREE FAL L OF LIQS IN EXCESS OF A FEW INCHES.

Respiratory Protection:WHERE VENTILATIONS IS INADEQUATE, USE NIOSH/MSHA
APPROVED RESPIRATOR.
Ventilation:PROVIDE GENL DILUTION/LOC EXHST VENT IN VOL & PATTERN TO
KEEP CONC OF INGS Protective Gloves:NITRILE/NEOPRENE RUBBER OR PVA GLOVES.
Eye Protection:CHEM WORK GOGS & FULL LNGTH FSHLD
Other Protective Equipment:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES. WEAR PROTECTIVE CLOTHING, INCLUDING IMPERMEABLE APRON.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRE FIGHT PROC: AUTOIGNIT/EXPLO WHEN EXPOSED TO EXTREME HEAT. IF H*2O
IS USED, FOG NOZ PREF. EXPLO HAZ: HOT SURFS. TOX GASES MAY FORM
WHEN PROD IS CONTACTED BY FLAME/HOT SURFS. VENT: LEL TO REMOVE DECOM PRODS DURING WELDING/FLAMECUTTING ON SURFS COATED
W/PRODUCT. FIRST AID PROC: PERSIST SKIN/EYE IRRIT.

HCC:F4
Boiling Pt:B.P. Text:212F,100C
Vapor Pres:0.7
Vapor Density:HVR/AIR
Spec Gravity:1.30
Evaporation Rate & Reference:11 (BUAC=100)
Solubility in Water:0.0%
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF
SOLVENTS.
Percent Volatiles by Volume:54.5

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIS, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:THERM
DECOMP/WELDING/BRAZING/FLAME-CUTTING ON SURFS COATED W/PROD MAY
PRDCE FUMES INCLDG: CO, ZINC OXIDE.

Waste Disposal Methods:WASTE MATL MUST BE DISPOSED OF I/A/W FEDERAL,
STATE, PROVINCIAL, & LOCAL ENVIRON CONTROL REGS. EMPTY CNTNRS SHLD
BE RECYCLED OR DISPOSED OF THRU AN APPROVD WASTE MANAGEMENT
FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.